Play Modes for Elektron Octatrack
Play patterns reversed, pingpong, random or shuffled, or hold trig keys to repeat steps: per pattern, shared by every track or set per track.
Module version 0.2.0-experimental. Base firmware: 1.40C.
About this module
Play Modes changes which step the sequencer plays at each position: NORMAL, REVERSED, PINGPONG (end steps once), PINGPONG 2 (end steps twice), RANDOM or SHUFFLE. Each pattern keeps its own modes: one shared mode under SCALE MODE NORMAL, one per audio and MIDI track under PER TRACK. Trigs, conditions, micro-timing, swing and locks move with their step; tempo, lengths, chains and the trig LEDs stay in step. The modes are saved with the project, survive a power cycle and follow pattern copy, paste and clear. REPEAT plays normally until trig keys are held while playing; then the track loops only the held steps, and on release it continues from where the stock playhead has reached.
- Six playhead modes, including two pingpongs and a shuffle that plays every step once per pass
- STEP REPEAT: hold trig keys to loop those steps, let go to land back in time
- Per pattern; per track under PER TRACK scale mode, audio and MIDI tracks
- Hold a TRACK key and press UP or DOWN; a popup names the mode
- Saved in the project, kept over a power cycle, carried by pattern copy and paste
How to use it
- Hold a TRACK key and press DOWN to step through NORMAL, REVERSED, PINGPONG, PINGPONG 2, RANDOM, SHUFFLE and REPEAT; UP walks back. The popup shows ALL <mode> under SCALE MODE NORMAL, or T1..T8 / M1..M8 <mode> under PER TRACK.
- In REPEAT, press PLAY and hold trig keys: the track loops the held steps in step order; let go and it continues from where it would have been.
- Each pattern keeps its own modes; PLAY and every pattern change start the tracks from their first step again.
- Under PER TRACK, MASTER LENGTH limits how far a track gets; set it to INF to let every track run its full length in every mode.
Compatibility notes
- Does not combine with octabam's PLOCKS P2 (not in this catalog): both use battery RAM 0x100f8600.. and the 20 pattern-copy memcpy sites.
- Deliberate stock-flow change: TRACK held + UP / DOWN changes the mode and does not reach the stock arrow handler; project.work gains #PLAY_MODES= comment lines.
- Deliberate stock-flow change (0.2.0, REPEAT only): while the sequencer plays and the current track is in REPEAT, the trig keys in TRACKS trig mode loop steps and no longer trigger tracks; stopped, GRID REC, LIVE REC and the other trig modes stay stock.
- Copying a single track does not copy its mode; PROJECT > NEW may keep the previous project's modes (untested).
- Played interactively on one MKII (builds 12-24); MKI, micro-timing, trig conditions, slides, live recording and MIDI tracks beyond a first check are untested.
- Chip worst-case cycles are unmeasured; no stress project has been run.
- Like every DRAM module, the build gives up about 10 MB of sample memory to the platform reserve.
- Build-24 physical reboot, Part/project save-reload after later edits and distinct-track isolation were not rechecked; build-19 persistence results remain historical.
- STEP REPEAT (0.2.0) is host-tested and run under the ColdFire port only: not played on a unit; MKI, audio and MIDI out, PER TRACK and patterns longer than 16 steps under REPEAT are untested; on long patterns the keys name the playhead's page.
Test evidence
Host suites for the engine and firmware glue pass, including STEP REPEAT's; instruction counts in octabam's ColdFire core for 0.2.0 bound one track step at 4,746 instructions (1,969 measured); STEP REPEAT ran under the ColdFire port on a real project (GRID REC, LIVE REC, CHROMATIC, stopped and a MIDI track left stock). The author's MKII report covers 0.1.1's build 24 and is historical for 0.2.0; 0.2.0 has not been played on a unit. No stress run, no chip timing.
Module source and documentation